CS 5500 Operator's Guide
Links on this page:   Installing the CS 5500  |  Ports on the CS 5500  |  Placing the CS 5500  |  Connecting the CS 5500  |  Installation on a single telephone line  |  Connecting the CS 5500 to an ADSL Phone Line
Installing the CS 5500 (return to top)

The CS 5500 is a single line device that can be installed on any type of modular system that consists of one or more lines, with one or more phones. A modular system consists of phone cables that can be connected and disconnected from a telephone device.
Ports on the CS 5500 (return to top)
The rear panel of the CS 5500 includes four (4) modular ports and a power input port, as shown:

1. Connect a single telephone line from a standard telephone (wall) jack to this port. The CS 5500 will transfer all voice calls to the TAD and PHONE ports simultaneously.
2. Connect your Telephone Answering Device (TAD) or integrated phone/answering machine to this port. The CS 5500 will transfer all voice calls to the TAD and PHONE ports simultaneously.
 4. The fax machine must be connected to the FAX/MODEM port to enable the CS 5500 to automatically transfer a fax call with a fax CalliNG (CNG) tone to the fax machine. A computer modem or fax/modem can also connect to this port in lieu of a fax machine.
3. Depending on the installation, a single line phone, an integrated phone/answering machine, multiple phones, or a telephone system (KSU or PBX) can be connected to this port.

(See "Special operating notes" for an explanation of CNG tones.)
Placing the CS 5500 (return to top)

The CS 5500 can be placed on either a flat surface, or mounted on a wall with the connected telephone line cords above or below the unit. To mount on a wall, follow these steps:

1.

Mark the positions for 2 mounting screws (not supplied) on the wall. The positions should be 3 1/4" apart (vertically). Drill the 2 holes, then thread the screws into the wall. The screws should extend 3/16". Do not over tighten the screws.
2.

Align the keyholes on the back of the CS 5500 with the 2 screws, then push in and press down to secure it to the wall.


NOTE: If you place the CS 5500 on a flat surface, do not place it in close proximity to any peripheral equipment (approximately 2 to 3 feet away from all electronic equipment).
Connecting the CS 5500 (return to top)

This section explains how to install the CS 5500 in most phone configurations that appear in a home or office. You can install the CS 5500 into one of the following phone configurations:

 a single telephone line

 a telephone system

Installation procedures for each of these configurations are provided in the following sections.

To perform the installation procedures in the following sections, you may need the following equipment:
 

telephone cables to connect the CS 5500 to your telephone (wall) jack.
  

extension cables--required if the connecting equipment is not located near the CS 5500.
  

additional telephone cables -- typically supplied with equipment by the manufacturer. You need additional telephone cables for as many pieces of equipment as you intend to connect to the CS 5500. If the equipment manufacturer does not provide the required cables, you can purchase them at a consumer electronics store.
Installation on a single telephone line (return to top)

The following diagram shows a complete installation for a single phone line connection. While the connections to the telephone (wall) jack may be different for other types of phone systems, the connections to the CS 5500 remain the same for all phone configurations.

1.

Plug one end of a telephone line cord into the LINE-IN port on the CS 5500. Plug the other end of the modular line cord into the telephone (wall) jack.

 4.

To connect a phone, plug one end of a modular line cord into the PHONE port on the CS 5500.
2.

Plug the small end of the AC power cord provided with the CS 5500 into the power input port labeled "12 VAC" on the CS 5500. Plug the adapter into a standard AC outlet.

The green LED flashes rapidly for about 5 seconds when power is applied and then remains illuminated, indicating its ON status.

 5.

To connect a fax machine, plug one end of a modular line cord into the FAX/MODEM port on the CS 5500.

Set the fax to answer on 1 ring.
3.

To connect an answering machine, plug one end of a modular line cord into the TAD port on the CS 5500.

 6.

To connect a telephone device such as a computer modem,in lieu of a fax machine, plug one end of a modular line cord into the FAX/MODEM port on the CS 5500.

Set the modem to answer on 1 ring.
NOTE: To connect a Caller ID device with the CS 5500, simply plug the Caller ID into the PHONE port, then plug your phone into the Caller ID.
The factory setting for Caller ID operation is OFF.

To turn Caller ID ON, perform the following steps:

1.

Take the phone in the PHONE port off-hook
2.

Press # * 116 * (three beeps) 402 * (three beeps) *
3.

Hang up the phone

To turn Caller ID OFF, perform the following steps:

1.

Take the phone in the PHONE port off-hook
2.

Press # * 016 * (three beeps) 401 * (three beeps) *
3.

Hang up the phone
NOTE: Caller ID is a service provided by your local telephone company. (Service activation required.)
Connecting the CS 5500 to an ADSL Phone Line

Two 8K In-Line Microfilter phone filters are required - available from most consumer electronics stores. Connect your filters as shown below:
1. Connect the two filters together in series.
2. Plug one end of the connected filters into the telephone (wall) jack.
3. Plug the other end into the LINE-IN port on the CS 5500.
(return to top)